Merit LILIN VS212 Release Note

================================================================================
1.0.80
Fixed Items
1.Fixed the PTZ component to be disappeared after update from 1.0.62.
2.Fixed if it is in MLP1 protocol, the NVR now via the web browser can call the preset points, 180 degrees, AutoPan and Stop AutoPan.
3.Fixed if it is in MLP1 protocol, call the preset point 1 and it runs the preset point 2.
4.Fixed if it is in MLP1 protocol, call the preset point 128 and it will be unfocused. Also, the Focus and Auto Focus features don't work.
5.Fixed if it is in MLP1 protocol by using Navigator software to control the preset point which may get unexpected error.

1.0.62
Fixed Items
1.Supported the IE11 browser.
2.Fixed if the HTTP Port is not 80, the SD card webpage doesn't show the video when playback.
3.Modified the buttons of SD card playback webpage and the size of the screen when playback.
4.Added the feature if the watchdog reboots three time in a row, the video setting goes back to default.
5.If the SD card is in always record mode, the time interval between the recorded files get reduced.
6.Fixed when using the quicktime to play the UDP stream, there is no audio output.
7.Fixed the frame rate limited in ONVIF.
8.Added the Turkish language.
9.Fixed when connected with the NVR if the frame rate low which can get video loss easily.
10.Fixed the VS212 that the date and time can be adjusted via NVR.
11.Fixed if using the external RTC, when boot up the VS212, it doesn't use the external RTC.
12.Modified the typesetting for tamper webpage.
13.Modified the operator rights. If an operator is created by administrator, the "Administrator" box is not checked and the "Panel Control" is checked so that the administrator can add this operator as admin right at any time.
14.Fixed when using the IPScan to change the IP address if the IPCam is connected by NVR or CMX, the H264 and JPEG get stuck by 1 online user.
15.Fixed the avi files of the SD card recording that the pre-recording and the current triggered recorded video files are both included the wrong video data.
16.Fixed if continuously click the video files to playback the files in SD card, it can cause the files not to be playback properly.
17.When enable the "Bypass Logon" feature, the RTSP authentication will be disabled.
18.Fixed when the face detection is enabled but there is no log recorded.
19.The baseline mode is removed and the only setting is main profile now.
20.Updated the ActiveX to 1.0.50.112 version which supports to show up the ActiveX recording time.
21.Fixed the old UI when edit a user or operator, other permission checkbox is disabled and can't be selected.

1.0.54
Fixed Items
1. Added the audio on or off button on web.
2. Added the alarm auto trigger output to be on or off.
3. Added Korean language.
4. Added Simplify Chinese language.
5. Added the format SD card feature.
6. Added the RTSP authentication item and the default setting is off.
7. Added the encode mode option for selecting baseline and main profiles.
8. Added the time zone (GMT +10:00) for Canberra, Melbourne and Sydney with the audio to be off.
9. Added the SD card recording event to the system log and also supported to download the videos from the SD card.
10. Supported the DDNS to add "_" symbol.
11. Added the IPScan Bypass Logon feature.
12. Added the ONVIF supported items to the HTTP/RTSP webpage.
13. Added the Daylight Saving feature.
14. Added a button to update the DDNS manually.
15. Added the IP address filtering.
16. Added to play the video on SD card on web.
17. Supported the mask feature after the pan/tilt version 1.6.13 added.
18. Added SDDP feature.
19. Removed the "Delete Log" feature.
20. Modified the size of the video on the homepage.
21. Upgraded the ActiveX to 1.0.50.96 version.
22. Modified the first stream to support 10Mb bitrate for each profile.
23. Added the feature to download a bactch files from SD card at the same time.
24. Fixed the display issue on IE10
25. Optimized the PPPoE dial up procedure.
26. Fixed the issue if the network is in poor condition which caused the pan/tilt non-stop.


1.0.504
Fixed Items
1. Fixed the 960H speed dome when the video quality setting is modified, reboot the camera but the setting doesn't take place.
2. Fixed the playback speed issue of 960H speed dome when record the videos using SD card.
3. Added the feature of 960H speed dome H264 when AutoPan the speed, it must stop the AutoPan action before save the settings.
4. Fixed the video loss issue when run the cameras with NVR.
5. Updated the ActiveX to version 1.0.50.77.
6. Modified the default video quality settings of the brightness to -6, contrast to -6, Hue to 0, saturation to 28 and sharpness to 12.


Device Support List
1. 960H speed dome, VS212, IPS722 & IPS622 1.3 MP IP Speed Dome camera

Update firmware from web interface

1.Login into the IP Camera via IE.
2.Click on Configure->System->Firmware Update
3.Click on "Browse" button to locate the firmware file, flasham.bin.
4.Click on "OK" button.
5.Wait the web interface to be reloaded again.

WARNING!
YOU DO NOT HAVE TO UPGRADE THE LATEST FIRMWARE.  HOWEVER, THE LATEST FIRMWARE CAN
IMPROVE THE DEVICE's SYSTEM PERFORMANCE.  THERE ARE ALSO RISKS FOR UPGRADING THE NEW
FIRMWARE INCLUDING POWER FAILURE, LOW BANDWIDTH, or FLSAH DISK BROKEN.  
THE RESULT MAY REQUIRE RETURNING the DVR BACK TO YOUR ORIGINAL PROVIDER 
FOR REPAIRING.
================================================================================
Version 1.0.500 (2013/1/21)

Fixed Items
1. Updated the ActiveX to 1.0.50.77 version.
  -Fixed the Live Image broken issue when set up the video port to RTSP/UDP.
2. Fixed the H264 video data when added the camera to the NVR which sometimes shows video loss messages.
3. Modified the system reboot countdown time to 90 seconds.
4. Fixed the ftp sending 0KB file issue.


Version 1.0.492 (2012/11/08)
First release
Note, 960H speed dome, VS212, HD 1.3 MP IP Speed Dome use the firmware.

